manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 235 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 235

Workshop Manual, TPD 1350, issue 3

235

 

21

New 1000 Series

10  Lightly lubricate the oil seal (A2) with clean engine 
lubricating oil. Put the tapered tool PD.247 onto the 
drive shaft with the tapered end towards the bearing. 
The tapered tool ensures that the lip of the oil seal is 
correctly fitted when the seal is pressed into position.

11  Lubricate the oil seal with clean engine oil. Push 
the oil seal over the tapered tool and into position in 
the pump body with the flat face of the seal towards 
the impeller end.

12  Press the oil seal into the oil seal housing:

A tool (B) can be made to press the new oil seal into 
position. The tool should be made of steel to the 
dimensions shown below:

A 40,0 mm (1.57 in)

B 80,0 mm (3.15 in)

C 60,0 mm (2.36 in)

D 42,0 mm (1.65 in)

E 29,0 mm (1.14 in)

F 14,5 mm (0.57 in)

G 12,0 mm (0.47 in)

The dimensions of the tool to fit the oil seal, will 
ensure that the seal is in the correct position after it is 
installed. It will also prevent axial distortion of the seal 
when it is pressed onto the shaft.

13  Use tool (B) and press the oil seal into the body 
until the seal is 14,5 mm (0.57 in) from the end of the 
flange for the coolant seal (A1). When the seal is in 
position, continue to apply force for approximately ten 
seconds to ensure that the seal remains in position 
when the force is released. Clean off excess oil.

Continued

A

A0377D

2

1

A

E

D

C

G

F

B

B

A1450

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов