manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 167 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 167

Workshop Manual, TPD 1350, issue 3

167

 

19

New 1000 Series

Lubricating oil pump

To remove and to fit

19-6

For four cylinder engines fitted with a balancer unit, 
the oil pump is integral with the balancer unit, 

see 

section 14

 for removal instructions.

The lubricating oil pump has a channel (B1) in the 
body of the pump. Lubricating oil from the front main 
bearing passes down the channel in the body of the 
pump to an oil hole in the idler shaft. The lubricating 
oil then passes through the hole in the idler shaft to 
the bush in the idler gear.

To remove

1  Drain the lubricating oil and remove the lubricating 
oil sump

, see operation 19-3

.

2  Remove the suction pipe and strainer

, see 

operation 19-4

.

3  For four cylinder engines: Remove the oil pressure 
relief valve

, see operation 19-9

, and the delivery pipe. 

For six cylinder engines: Remove the delivery pipe of 
the oil pump.

4  The oil pump is fitted to number 1 main bearing cap. 
The oil pump can be removed with the main bearing 
cap, if a suitable spanner is available that will enable 
the torque to be applied correctly to the setscrews of 
the main bearing cap when it is fitted. If a suitable 
spanner is not available, the timing case must be 
removed, 

see operation 15-9

.

5  Release the circlip which retains the idler gear of 
the oil pump and remove the washer (A1) and the 
idler gear (A2).

6  Release the setscrews and remove the oil pump 
(B).

3

2

1

A

A0228

1

B

A0229

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов