manualshive.com logo in svg

Perkins New 1000 Series, Руководство по ремонту, Страница: 73 / 290

Поделиться
Скачать
Perkins New 1000 Series Скачать руководство пользователя страница 73

Workshop Manual, TPD 1350, issue 3

73

 

13

New 1000 Series

To check the length of a
connecting rod

13-7

A partially finished small end bush, which can be fitted 
to the original connecting rod and machined to obtain 
the correct length grade is available

, see operation 

13-10

. Specialist equipment and personnel with the 

correct training are needed to machine the partially 
finished small end bush. 

Connecting rod kits are also available with the small 
end bush fitted and machined to obtain the correct 
connecting rod grade.

Cautions:

!

It is important that the piston does not contact the 
cylinder head. Ensure that the piston height above 
the cylinder block is correct.

!

Ensure that the connecting rods are fitted in the 
correct cylinder. Record the position of the 
connecting rod and its relevant cylinder when it is 
removed from the engine.

To ensure that the piston height above the cylinder 
block is correct, the engine may have up to six length 
grades (F to L) of connecting rods fitted.

Identification of the length grade is by a letter or colour 
which is marked on the side of each connecting rod 
(A1). The letter F is the longest grade of connecting 
rod and letter L is the shortest grade. The difference 
between grades is 0,046 mm (0.0018 in).

If the grade letter or colour on the side of the 
connecting rod cannot be seen the length can be 
checked by the measurement of the dimension (x) 
shown in (A). Before the length of the connecting rod 
is measured, ensure that the bores of the big end and 
the small end are square and parallel

, see operation 

13-10

. The length is checked with the big end bearing 

removed and the original small end bush fitted. The 
dimensions for each grade are listed in the table 
below:

Grade

letter

Colour code

Length

(mm)

F

Red

165,728/165,761

G

Orange

165,682/165,715

H

White

165,637/165,670

J

Green

165,591/165,624

K

Purple

165,545/165,578

L

Blue

165,499/165,532

A

G0009

1

X

Purchased from www.WorkshopManuals.co.uk

Содержание New 1000 Series



































































































































































































































































































Отзывы:

Нет отзывов