Pentax DSI-200 Series Скачать руководство пользователя страница 159

Страница: 159 / 167

159

Definition of Communication Parameter Addresses

Read and Written Parameters Function parameters can be read and

written (except those which cannot be changed because they are

only for the factory use or for monitoring).

Parameter group No. and parameter identifying No. are used to

express parameter address.

● High-order bytes: P0 to PF (groups P), A0 to AF (groups A), 70

to 7F (group d)

● Low-order bytes: 00 to FF

For example, to read parameter P3-12, communication address of

F3-12 is expressed as 0xP30C

Note

● Group PF: The parameters cannot be read or changed.

● Group d: These parameters can only be read.

Some parameters cannot be modified when the AC drive is

running. Some parameter cannot be modified regardless of status

of the AC drive. In addition, pay attention to setting range, unit

and description of parameters when modifying them.

Parameter Group

Visited Address

Parameter Address in RAM

～

PE Group

0×F000

～

0×FEFF

0×0000

～

0×0EFF

～

AC Group

0×A000

～

0×ACFF

0×4000

～

0×4CFF

d0 Group

0×7000

～

0×70FF

Notes: Frequent storage to the EEPROM reduces its service life.

Содержание DSI-200 Series








































































































































































Результаты поиска

Содержание DSI-200 Series

Отзывы:

Похожие инструкции для DSI-200 Series

Бренды по названию

Популярные бренды

Pentax DSI-200 Series, Руководство пользователя

Результаты поиска

Содержание DSI-200 Series

Отзывы:

Похожие инструкции для DSI-200 Series

Бренды по названию

Популярные бренды