Pentax DSI-200 Series Скачать руководство пользователя страница 139

Страница: 139 / 167

- 139 -

Deceleration time is too
short.



Increase deceleration time.

Braking unit and braking
resistor are
not installed.



Install braking unit and braking
resistor.

Over

voltage at

constant

speed

FU07

The over voltage stall
prevention
parameters are set
improperly.



Ensure that the voltage limit function
is enabled (P3-23 )



The setting of voltage limit (F3-22)
is too large. Adjust it

between 700 V

and 770 V.



The setting of frequency gain for
voltage limit (P3-24) is too small.
Adjust it between 30 and 50.



The setting of frequency rise
threshold during voltage limit (P3-
26) is too small. Adjust it between 5
Hz and 20 Hz.

An external force drives
motor during
running.



Cancel the external force or install a
braking resistor

Pre-charge

resistor

fault

FU08

Input voltage is not in
arranged range



Arrange voltage in a reasonable range

Under

voltage

FU09

Instantaneous power failure
occurs



Enable the power dip ride through
function (P9-59 ).

The AC drive's input
voltage is not
within the permissible
range.



Adjust the voltage to normal range.

The bus voltage is
abnormal.



Contact the agent

The rectifier bridge, the
buffer

resistor, the drive

board or the

control board

are abnormal.



Contact the agent

AC drive

overload

FU10

Load is too heavy or
locked-rotor

occurs on

motor.



Reduce load or check motor and
mechanical conditions.

The AC drive power class
is small.



Replace a drive of larger power
class.

Motor

overload

FU11

P9-01 (Motor overload
protection

gain) is set

improperly.



Set P9-01 correctly.

Load is too heavy or
locked-rotor

occurs on

motor.



Reduce load or check motor and
mechanical conditions.

Содержание DSI-200 Series








































































































































































Результаты поиска

Содержание DSI-200 Series

Отзывы:

Похожие инструкции для DSI-200 Series

Бренды по названию

Популярные бренды

Pentax DSI-200 Series, Руководство пользователя

Результаты поиска

Содержание DSI-200 Series

Отзывы:

Похожие инструкции для DSI-200 Series

Бренды по названию

Популярные бренды