Pentax DSI-200 Series Скачать руководство пользователя страница 141

Страница: 141 / 167

- 141 -

Current

detection

failure

FU18

The hall is abnormal.



Replace the hall.

The drive board is
abnormal.



Replace the drive board.

Motor self-

learning

malfunction

FU19

Motor parameters are not
set

according to nameplate.



Set motor parameters correctly
according to nameplate.

Motor auto-tuning times
out.



Check the cable connecting AC drive
and motor.

The encoder is abnormal.



Check whether P1-27 (encoder
pulses per revolution) is set

correctly. Check whether signal lines
of encoder are connected correctly
and securely.

Encoder

fault

FU20

Encoder is not matched.



Set the type of encoder correctly.

Encoder wiring is incorrect.



Check the PG card power supply and
phase sequence.

Encoder is damaged.



Replace encoder.

PG card is abnormal.



Replace PG card.

EEPROM
read-write

fault

FU21

The EEPROM chip is
damaged.



Replace the main control board.

Short

circuit to

ground

FU23

Motor is short circuited to
the ground.



Replace cable or motor.

Accumulati

ve running

time

reached

FU26

Accumulative running time
reaches the setting value.



Clear the record through parameter
initialization.

User-

defined

fault 1

FU27

User-defined fault 1 is input
via S.



Reset the operation.

User-

defined

fault 2

FU28

User-defined fault 2 is input
via virtual S



Reset the operation.

Accumulati

ve power

reach error

FU29

Accumulative power-on
time reached



Use the parameter initialization
function

clear

the

record

information

Load loss FU30 Working current <P9-64



Check whether the load is off or P9-
64, P9-65 parameter set Whether to
meet the actual operating conditions

PID

feedback

lost during

running

FU31

PID feedback <PA-26 set
value



Check PID feedback or set

A-26

properly.

Содержание DSI-200 Series








































































































































































Результаты поиска

Содержание DSI-200 Series

Отзывы:

Похожие инструкции для DSI-200 Series

Бренды по названию

Популярные бренды

Pentax DSI-200 Series, Руководство пользователя

Результаты поиска

Содержание DSI-200 Series

Отзывы:

Похожие инструкции для DSI-200 Series

Бренды по названию

Популярные бренды