Pentax DSI-200 Series Скачать руководство пользователя страница 144

Страница: 144 / 167

- 144 -

not rotate after

the AC drive

runs.

drive and motor is normal.

Related AC drive and

motor parameters

Are set improperly.

Restore the factory parameters
and re-set the following



parameters properly:



Encoder parameters



Motor ratings, such as rate
motor frequency and rated



motor speed



Motor 1 control mode (P0-01)
and command source



selection (P0-02)



P3-01 (torque boost) in V/F
control under heavy-load start.

Cable connection between

drive board

And control board is in poor

contact.



Re-connect wirings and ensure
secure connection.

The drive board is faulty.



Contact the agent

S terminals are

disabled.

Related parameters are set

incorrectly.



Check and set parameters in
group F4 again.

External signals are

incorrect.



Re-connect

external

signal

cables.

Jumper across OP and +24 V

becomes

Loose.



Re-confirm the jumper bar
across OP and +24 V.

The control board is faulty.



Contact the agent.

Motor speed

does not rise in

FVC control.

Encoder is faulty.



Replace

encoder

and

re-

confirm cable connection.

Encoder connection is

incorrect or in poor

Contact.



Replace the PG card.

PG card is faulty.



Contact the agent

Drive board is faulty.

The AC drive

detects over

current and over

voltage

Frequently.

Motor parameters are set

improperly.



Set

motor

parameters

perform

motor

auto-tuning

again

Acceleration/deceleration

time is improper.



Set

proper

acceleration/deceleration time.

Содержание DSI-200 Series








































































































































































Результаты поиска

Содержание DSI-200 Series

Отзывы:

Похожие инструкции для DSI-200 Series

Бренды по названию

Популярные бренды

Pentax DSI-200 Series, Руководство пользователя

Результаты поиска

Содержание DSI-200 Series

Отзывы:

Похожие инструкции для DSI-200 Series

Бренды по названию

Популярные бренды