Oracle Sun Netra X4270 Скачать руководство пользователя страница 22

Страница: 22 / 238

Locating Server and Component LEDs

No.

Description

Color

Additional Information

OK to Remove

Blue

On – The drive is ready for hot-plug removal.

Off – Normal operation.

Fault

Amber

On – The drive has a fault and requires attention.

Off – Normal operation.

Activity

Green

On – The drive is receiving power. Solidly lit if drive is idle.

Flashing – The drive is processing a command.

Off – Power is off.

Related Information

■

“Front Panel Components on Two-Drive Systems With Bezel Removed” on page 15

■

“Front Panel Components on Four-Drive Systems With Bezel Removed” on page 16

■

“Replacing a Drive” on page 85

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды