manualshive.com logo in svg

Oracle Sun Netra X4270, Руководство по обслуживанию

Поделиться
Скачать
Oracle Sun Netra X4270 Скачать руководство пользователя страница 16

Locating Controls and Connectors

Front Panel Components on Four-Drive Systems

With Bezel Removed

No.

Description

Additional Information

1

Alarm status indicators

Top to bottom – Critical LED, Major LED, Minor LED, User

LED

Note - 

Also displayed through the front bezel

2

System status indicators

Left to right – Locator LED button, Service Required LED,

System Activity LED, Power button

Note - 

Also displayed through the front bezel

3

Drive 2

Labeled 2

4

Drive 1

Labeled 1

5

Drive 0

Labeled 0

6

Drive 3

Labeled 3

7

Drive LEDs

Top to bottom – OK to Remove LED, Fault LED, Activity

LED

Related Information

■

“System Status LEDs” on page 19

■

“User Alarm LEDs” on page 20

■

“Drive LEDs” on page 21

16

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды