Oracle Sun Netra X4270 Скачать руководство пользователя страница 160

Страница: 160 / 238

Replacing CPUs

Note -

If the SP is configured to synchronize with a network time server using the Network

Time Protocol, the ILOM SP clock will be reset as soon as the server is powered on and

connected to the network.

If the SP is not configured to use NTP, you must reset the ILOM service

processor clock using the ILOM CLI or the web interface.

For instructions, refer to the ILOM 3.0 documentation.

Related Information

■

“Remove the Battery” on page 158

■

Oracle Integrated Lights Out Manager (ILOM) 3.0 Web Interface Procedures Guide

■

Oracle Integrated Lights Out Manager (ILOM) 3.0 CLI Procedures Guide

Replacing CPUs

Caution -

Ensure that all power is removed from the server before removing or installing

a CPU. You must disconnect the power cables from the system before performing these

procedures.

Note -

When operating the system with one CPU, you must install a CPU filler cover in the

empty CPU slot.

The following topics are covered:

■

“Remove a CPU” on page 160

■

“Install a CPU” on page 163

■

“Install a Second CPU” on page 166

Related Information

■

“Replacing DIMMs” on page 132

Remove a CPU

Prepare the server for service.

160

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды