Oracle Sun Netra X4270 Скачать руководство пользователя страница 185

Страница: 185 / 238

Remove a Power Supply

FIGURE 17

Power Supplies and Latches

Figure Legend

Power Supply 0

Power Supply 1

A lighted amber LED on a power supply indicates that a failure was detected. You can also use

the ILOM

show

faulty

command at the

sc>

prompt.

Note -

The fans of a failed power supply may still be spinning when the system is powered on.

The failed power supply is still okay to remove.

Log in to the ILOM service processor as root.

Refer to the ILOM 3.0 documentation for instructions.

At the ILOM prompt (

), type the

stop /SYS/PS

command.

The

stop

command indicates if it is okay to perform a hot removal of a power supply. This

command does not perform any action, but it provides a warning if the power supply should not

be removed because the other power supply is not providing power to the server.

Replacing Chassis Components

185

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды