manualshive.com logo in svg

Oracle Sun Netra X4270, Руководство по обслуживанию

Поделиться
Скачать
Oracle Sun Netra X4270 Скачать руководство пользователя страница 147

Replacing the Flash Module Cable

See 

“Install the PCI Mezzanine” on page 104

.

9.

Return the server to operation.

See 

“Returning Server to Operation” on page 211

.

Related Information

■

“Remove a Flash Module” on page 144

Replacing the Flash Module Cable

Installed to connectors on the motherboard assembly in PCIe2 slot 1, the flash module cable is a

mini-SAS 36-pin to dual 7-pin SATA splitter cable. This cable must be installed in order for the

system to access the flash modules.

These tasks describe how to remove and install the flash module cable.

■

“Remove the Flash Module Cable” on page 147

■

“Install the Flash Module Cable” on page 148

Remove the Flash Module Cable

1.

Prepare the server for service.

See 

“Preparing the Server for Component Replacement” on page 75

.

2.

Remove the PCI mezzanine and place it on an antistatic mat.

See 

“Remove the PCI Mezzanine” on page 102

.

3.

If there is a PCIe2 card installed in PCIe2 slot 2, remove the card and place it on

an antistatic mat.

See 

“Remove the Lower PCIe2 Cards” on page 123

.

Replacing Motherboard Assembly Components

147

Содержание Sun Netra X4270















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды