Oracle Sun Netra X4270 Скачать руководство пользователя страница 63

Страница: 63 / 238

Understanding BIOS Setup Screens

For instructions on accessing the BIOS Setup utility, see

“Access the BIOS Setup Utility

Menus” on page 46

The following table contains descriptions of the top-level BIOS setup screens.

Menu

Description

Links

Main

General product information, including BIOS type,

processor, memory, and time/date.

“BIOS Main Menu Screens” on page 63

Advanced

Configuration information for the CPU, memory,

IDE, Super IO, trusted computing, USB, PCI, MPS

and other information.

“BIOS Advanced Menu

Screens” on page 64

PCI

Configure the server to clear NVRAM during

system boot.

“BIOS PCI Menu Screen” on page 65

Boot

Configure the boot device priority (storage drives

and the optical media drive).

“BIOS Boot Menu Screens” on page 66

Security

Set or change the user and supervisor passwords.

“BIOS Security Menu Screen” on page 67

Chipset

View the configuration of server chipsets.

“BIOS Chipset Menu

Screens” on page 68

Exit

Save changes and exit, discard changes and exit,

discard changes, or load optimal or fail-safe

defaults.

“BIOS Exit Menu Screen” on page 69

“Exit the BIOS Setup Utility” on page 70

Related Information

■

“Understanding BIOS Booting and Setup” on page 37

BIOS Main Menu Screens

The BIOS Main screens provide general product information, including BIOS, processor,

system memory, and system time/date. The following figure shows the BIOS Main top-level

screen.

Using the BIOS Setup Utility

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды