Oracle Sun Netra X4270 Скачать руководство пользователя страница 53

Страница: 53 / 238

Configure TPM Support

Configure TPM Support

If you intend to use the Windows 2008 TPM feature set, you must configure the server to

support this feature.

Note -

TPM enables you to administer the TPM security hardware in your server. For additional

information about implementing this feature, refer to the Windows Trusted Platform Module

Management documentation provided by Microsoft.

Access the BIOS Setup utility menus.

For instructions, see

“Access the BIOS Setup Utility Menus” on page 46

From the BIOS Main menu screen, select Advanced.

From the Advanced Settings screen, select Trusted Computing.

Using the BIOS Setup Utility

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды