Oracle Sun Netra X4270 Скачать руководство пользователя страница 78

Страница: 78 / 238

Power Down Server Gracefully Using the Power Button

This action causes ACPI-enabled operating systems to perform an orderly shutdown of the

operating system. Servers not running ACPI-enabled operating systems shut down to standby

power mode immediately.

When main power is off, the power OK LED on the front panel will begin flashing, indicating

that the server is in standby power mode. See

“System Status LEDs” on page 19

Disconnect the power and data cables from the server.

See

“Disconnect Cables From the Server” on page 80

Caution -

When you use the Power button to enter standby power mode, power is still directed

to the service processor remote management subsystem and power supply fans. To completely

power off the server, you must disconnect the AC or DC power cords from the back of the

power supplies.

Related Information

■

“System Status LEDs” on page 19

■

“Power Down Server Gracefully” on page 76

■

“Power Down Server For an Emergency” on page 79

■

“Disconnect Cables From the Server” on page 80

■

“Power On the Server” on page 214

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды