Oracle Sun Netra X4270 Скачать руководство пользователя страница 24

Страница: 24 / 238

Locating Server and Component LEDs

Description

Color

Additional Information

Power OK

Green

On – Normal operation. Output voltage is within normal limits.

Off – Power is off.

Fault

Amber

On – Failure detected.

Off – Normal operation.

Source OK

Green

On – Normal operation. Input power is within normal limits.

Off – No input voltage, or input voltage is below limits.

Related Information

■

“Rear Panel LED Locations” on page 23

■

“Replacing Power Supplies” on page 184

Ethernet Port LEDs

The ILOM SP NET MGT Ethernet port and the four Gigabit Ethernet ports each have two

LEDs.

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды