manualshive.com logo in svg

Oracle Sun Netra X4270, Руководство по обслуживанию

Поделиться
Скачать
Oracle Sun Netra X4270 Скачать руководство пользователя страница 23

Locating Server and Component LEDs

Rear Panel LED Locations

No.

Description

Additional Information

1

Power Supply 0 LEDs

Top to bottom – Locator LED, Service Required LED, Power OK LED

2

Power Supply 1 LEDs

Top to bottom – Locator LED, Service Required LED, Power OK LED

3

System LEDs

Left to right – Locator LED Button, Service Required LED, Power OK LED

4

Network Management port LEDs

Left to right – Link/Activity LED, Speed LED

5

Gigabit Ethernet port LEDs

Left to right – Link/Activity LED, Speed LED

Related Information

■

“Power Supply LEDs” on page 23

■

“System Status LEDs” on page 19

■

“Ethernet Port LEDs” on page 24

Power Supply LEDs

The power supply LEDs are located on the rear of each power supply.

Understanding the Server

23

Содержание Sun Netra X4270















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды