Oracle Sun Netra X4270 Скачать руководство пользователя страница 177

Страница: 177 / 238

Reset the BIOS Password and Clear the CMOS NVRAM

Related Information

■

“System Components” on page 25

■

“Field-Replaceable Units” on page 27

■

“Remove the Motherboard Assembly” on page 168

Reset the BIOS Password and Clear the CMOS NVRAM

You can clear the CMOS NVRAM and BIOS Password by pressing the CLR CMOS button,

which is located on the motherboard. You can also reset the BIOS passwords from the BIOS

Setup utility.

Caution -

Ensure that all power is removed from the server before removing or installing

the motherboard assembly. You must disconnect the power cables from the system before

performing these procedures.

Prepare the server for service.

See

“Preparing the Server for Component Replacement” on page 75

Remove the PCI mezzanine.

See

“Remove the PCI Mezzanine” on page 102

Replacing Motherboard Assembly Components

177

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды