manualshive.com logo in svg

Oracle Sun Netra X4270, Руководство по обслуживанию

Поделиться
Скачать
Oracle Sun Netra X4270 Скачать руководство пользователя страница 25

System Components

FIGURE   2

Ethernet Port LEDs

No.

Description

Color

Additional Information

1

Link/Activity

LED

Green

Steady On – A link is established.

Blinking – There is activity on this port.

Off – No link is established.

2

Speed LED

Amber or

green

Amber – The link is operating as a 1000 Mbps connection.

Green – The link is operating as a 100 Mbps connection.

Off – The link is operating as a 10/100 Mbps connection.

Note - 

The NET MGT port operates only in 100-Mbps or 10-Mbps so the speed indicator LED

can be green or off (it will never be amber).

Related Information

■

“Rear Panel LED Locations” on page 23

■

“Disconnect Cables From the Server” on page 80

■

“Reconnect Power and Data Cables” on page 213

System Components

The following figure identifies the major components of the server.

Understanding the Server

25

Содержание Sun Netra X4270















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды