Oracle Sun Netra X4270 Скачать руководство пользователя страница 80

Страница: 80 / 238

Disconnect Cables From the Server

■

“Power Down Server Gracefully Using the Power Button” on page 77

■

“Disconnect Cables From the Server” on page 80

■

“Power On the Server” on page 214

Disconnect Cables From the Server

Caution -

The system supplies standby power to the circuit boards even when the system is

powered off.

Label all cables connected to the server.

Disconnect the power cables from the rear of the server.

Disconnect all data cables from the rear of the server.

If your rackmount kit includes a cable management device, remove the cables

from it.

Remove the server from the rack.

Related Information

■

“Rear Panel Cable Connections” on page 17

■

“Powering Down the Server” on page 76

■

“Remove the Server From the Rack” on page 80

■

“Reconnect Power and Data Cables” on page 213

Remove the Server From the Rack

Remove the server from the rack.

Remove the server from the rack prior to performing component replacement procedures. Make

sure to place the server on a stable work surface.

Caution -

The server weighs approximately 41 lbs (18.6 kg). Two people are required to

dismount and carry the chassis.

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды