Oracle Sun Netra X4270 Скачать руководство пользователя страница 168

Страница: 168 / 238

Replacing the Motherboard Assembly

11.

Replace the air duct.

See

“Install the Air Duct” on page 130

12.

Return the server to operation.

See

“Returning Server to Operation” on page 211

Related Information

■

“Remove a CPU” on page 160

■

“Install a Second CPU” on page 166

Replacing the Motherboard Assembly

Prepare a large antistatic mat in a dust-free work area before replacing the motherboard

assembly. When replacing the motherboard assembly, you will remove the following

components and associated cables:

■

Air duct

■

PCI Mezzanine

■

PCI risers

■

Fan tray 0

■

DIMMs

■

Flash modules and flash module cable

■

ESM riser

■

CPUs

■

Media bay assembly

Place these removed components on an antistatic mat in this dust free work area.

■

“Remove the Motherboard Assembly” on page 168

■

“Install the Motherboard Assembly” on page 172

Related Information

■

“System Components” on page 25

Remove the Motherboard Assembly

Prepare the server for service.

168

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды