Oracle Sun Netra X4270 Скачать руководство пользователя страница 166

Страница: 166 / 238

Install a Second CPU

set /SYS/MB/P0 clear_fault_action=true

Are you sure you want to clear /SYS/MB/P0 9y/n)?

Set ???clear_fault_action” to ???true???

Related Information

■

“Remove a CPU” on page 160

■

“Install a Second CPU” on page 166

Install a Second CPU

Prepare the server for service.

See

“Preparing the Server for Component Replacement” on page 75

Remove the air duct.

See

“Remove the Air Duct” on page 127

Remove the CPU filler cover from the empty CPU socket.

Clean the top of the CPU with the provided alcohol wipe.

Place the CPU in the socket with the correct orientation.

166

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды