Oracle Sun Netra X4270 Скачать руководство пользователя страница 86

Страница: 86 / 238

Remove a Drive

■

The drive provides the operating system, and the operating system is not mirrored on

another drive.

■

The drive cannot be logically isolated from the online operations of the server.

If your drive falls into one of these conditions, you must shut the system down before you

replace the drive. See

“Powering Down the Server” on page 76

Note -

Replacing a drive does not require removing the server from a rack.

Related Information

■

“Drive LEDs” on page 21

■

“Remove a Drive” on page 86

■

“Install a Drive” on page 89

Remove a Drive

Prepare the system for the drive removal:

■

“Take Antistatic Measures” on page 81

■

“Open Front Bezel” on page 84

Identify the location of the drive that you want to remove.

The following illustrations show the location of the drives and how the system numbers them.

FIGURE 5

Drive Location and Numbering on a Two-Drive Server

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды