Oracle Sun Netra X4270 Скачать руководство пользователя страница 39

Страница: 39 / 238

Understanding BIOS Booting and Setup

Event

Cause

Boot continues

on host?

Option ROM initialization

BIOS initializes Option ROMs

System firmware progress

Does not apply

Option ROM space exhausted

BIOS cannot copy an option to the memory

Yes

User initiated system set up

User initiated access to BIOS Setup utility

System firmware progress

Does not apply

User initiated boot to OS

System boot initiated

System firmware progress

Does not apply

No bootable media

Nothing to boot from

PXE server not found

Boot error - PXE server not found

F12 key was pressed but BIOS fails to boot from PXE server

ACPI Power state

Soft-off power applied

Does not apply

Related Information

■

“BIOS POST F1 and F2 Errors” on page 39

■

“BIOS POST Memory Testing Process” on page 41

BIOS POST F1 and F2 Errors

Each POST diagnostic is a low-level test designed to pinpoint faults in a specific hardware

component. If the POST diagnostic discloses an F1 or F2 error, it typically reports the following

information about the error:

■

Type of error detected

■

When or where the error occurred

The following table lists some of the F1 and F2 error messages that could appear during the

POST diagnostics along with instructions for how to possibly resolve the error reported.

TABLE 4

BIOS POST F1 and F2 Error Messages

BIOS POST Error Message

Error Type

Resolution

Uncorrectable Error Detected on Last Boot:IOH(0) Protocol

Error (Please Check SP Log for more Details)

IOH error

■ Press F1 to continue.
■ Check the SP event log in ILOM for more details.

Uncorrectable Error Detected on Last Boot:IOH(0) QPI [

]

Error (Please Check SP Log for more Details)

IOH error

■ Press F1 to continue.
■ Check the fault management function and the SP

event log in ILOM for more details.

Using the BIOS Setup Utility

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды