Oracle Sun Netra X4270 Скачать руководство пользователя страница 60

Страница: 60 / 238

Option ROM Allocation

Option ROM Allocation

The system BIOS allocates 128 Kbytes of address space for Option ROMs. This address

space is shared between on-board devices and PCIe2 plug-in cards. This fixed address space

limitation is imposed by the PC architecture and not by the BIOS itself. It is possible to exhaust

the available address space when installing PCIe2 plug-in cards. When the address space is

exhausted, the BIOS displays an

Option ROM Space Exhausted

message, which means that

one or more devices cannot load Option ROMs.

By default, all on-board Options ROMs are enabled in the BIOS. However, you can disable

most of these Option ROMs, unless they are required to support booting from the associated

device or to provide some other boot time function (such as a video controller or the hardware

RAID supported through the SAS controller HBA installed in PCIe2 slot 3). For example, it

is not necessary to load the Option ROM for the on-board network ports unless you mean to

boot from one or more network ports (even then, you can disable the Options ROMs for the

remaining ports).

To enable or disable Option ROMs, see

“Enable or Disable Option ROM

Settings” on page 60

For example, if you install a SCSI PCIe2 card and you encounter the

Option ROM Space

Exhausted

message, you can either:

■

Disable the Option ROM for the PCIe2 slot you installed the SCSI card in if you will not be

booting from that device.

■

Disable one or more Option ROMs for on-board devices (or slots populated with other plug-

in cards) to ensure there is room to boot from the desired device.

Related Information

■

“Access the BIOS Setup Utility Menus” on page 46

■

“Enable or Disable Option ROM Settings” on page 60

■

“Install PCIe2 Cards Into Slots 4 and 5” on page 117

■

“Install the SAS Controller HBA” on page 120

■

“Install the Lower PCIe2 Cards” on page 125

Enable or Disable Option ROM Settings

The BIOS Option ROM is 128 Kbytes. Of these 128 Kbytes, approximately 80 Kbytes are used

by the VGA controller, the disk controller, and the network interface card. Approximately 48

Kbytes remain to be shared by the Option ROMs on all bootable PCIe2 plug-in cards.

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды