Oracle Sun Netra X4270 Скачать руководство пользователя страница 85

Страница: 85 / 238

Close Front Bezel

■

“Close Front Bezel” on page 85

■

“Replacing a Drive” on page 85

■

“Replacing the Optical Media Drive” on page 91

■

“Replacing the Air Filter” on page 179

Close Front Bezel

Hold the green tabs on either side of the bezel, and lift up until the bezel snaps in

place.

Related Information

■

“Open Front Bezel” on page 84

Replacing a Drive

Note -

To ensure performance and reliability, only use carrier-grade NEBS-certified drives with

supported brackets.

■

“Drives Hot-Plug Conditions” on page 85

■

“Remove a Drive” on page 86

■

“Install a Drive” on page 89

Related Information

■

“Opening and Closing the Front Bezel” on page 83

Drives Hot-Plug Conditions

The solid-state or hard-disk drives in the server are hot-pluggable, but this capability depends

on how the drives are configured. To hot-plug a drive you must be able to take the drive offline

before you can remove it. When you take the drive offline, you prevent any application from

accessing the drive and remove the logical software links to the drive.

The following situations inhibit the ability to perform hot-plugging of a drive:

Replacing Storage Components

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды