Oracle Sun Netra X4270 Скачать руководство пользователя страница 76

Страница: 76 / 238

Power Down Server Gracefully

Related Information

■

“Returning Server to Operation” on page 211

Powering Down the Server

Determine how you want to power off the server.

Description

Link

Power the server down gracefully to prevent data from being

corrupted.

“Power Down Server Gracefully” on page 76

“Power Down Server Gracefully Using the Power

Button” on page 77

If the server is not responding, or you must shut down the

server quickly, perform an emergency power down.

“Power Down Server For an

Emergency” on page 79

Related Information

■

“Power On the Server” on page 214

Power Down Server Gracefully

Performing a graceful shut down ensures that all of your data is saved and the system is ready

for restart.

Log in to the server as superuser or equivalent.

Depending on the nature of the problem, you might want to view the system status, the log files,

or run diagnostics before you shut down the system. See

“View Event Logs” on page 48

for log

file information.

Notify affected users.

Refer to your operating system documentation for specific instructions.

Save any open files and quit all running programs.

Refer to your application documentation for specific information on these processes.

Log in to the ILOM SP to display the ILOM prompt.

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды