Oracle Sun Netra X4270 Скачать руководство пользователя страница 162

Страница: 162 / 238

Remove a CPU

CPU 1 LED

Using an Allen wrench, unscrew the two screws from the heatsink for the faulty

CPU [2].

Turn the screws alternately one and one-half turns until they are fully removed.

Twist the heatsink slightly to break the grease seal, lift off the heatsink and

place it upside down on a flat surface to prevent the thermal grease from

contaminating other components.

Caution -

Failure to clean the heatsink and the CPU prior to removing the CPU could result in

the accidental contamination of the CPU socket or other components. Also, be careful not to get

the grease on your fingers, as this could result in contamination of components.

162

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды