Oracle Sun Netra X4270 Скачать руководство пользователя страница 163

Страница: 163 / 238

Install a CPU

Use an alcohol pad to clean the thermal grease from both the bottom of the

heatsink and the top of the CPU.

You will use this heatsink when you install a replacement CPU.

Disengage the CPU release lever by pushing down and moving it to the side

away from the CPU, and then rotating the lever upward [3].

Open the pressure frame, carefully remove the CPU [4], and place the CPU on

antistatic mat.

10.

If you are not replacing the CPU, install a CPU filler cover on the empty slot.

Related Information

■

“Install a CPU” on page 163

■

“Install a Second CPU” on page 166

Install a CPU

Attach an antistatic wrist strap.

Unpack the replacement CPU.

Properly orient the CPU with the socket alignment tabs and carefully place the

CPU into the socket [1].

Replacing Motherboard Assembly Components

163

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды