Oracle Sun Netra X4270 Скачать руководство пользователя страница 110

Страница: 110 / 238

Install a PCIe2 Riser

If there is a PCIe2 card installed in the riser, place the riser an antistatic mat. Note in which slot

the PCIe riser was originally installed.

Related Information

■

“PCIe2 Riser Location and Differences” on page 107

■

“Install a PCIe2 Riser” on page 110

■

“Replacing PCIe2 Cards in Slots 4 and 5” on page 115

Install a PCIe2 Riser

Note -

The motherboard connector for PCIe2 riser 0 is different than the connector used by

PCIe2 risers 1 and 2. Do not attempt to install a PCIe2 riser in a different location on the

motherboard.

Determine into which slot you will install the PCIe2 riser.

See

“PCIe2 Riser Location and Differences” on page 107

110

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды