Oracle Sun Netra X4270 Скачать руководство пользователя страница 157

Страница: 157 / 238

Replacing the Battery

11.

Install the PCI mezzanine.

See

“Install the PCI Mezzanine” on page 104

12.

Install the air duct.

See

“Install the Air Duct” on page 130

13.

Return the server to operation.

See

“Returning Server to Operation” on page 211

14.

After replacing the faulty ESM, clear the server fault.

Refer to the ILOM 3.0 documentation for more information about the following steps.

Use the ILOM CLI to log in to the server as

root

and type the following

command to list all known faults on the server:

show /SP/faultmgmt

The command lists all known faults, for example:

show /SP/faultmgmt

  Targets:
     0 (/SYS/ESMR/ESM)
  Properties:
  Commands:
      cd
      show

Type the following command to clear the fault.

set /SYS/ESMR/ESM clear_fault_action=true

For example:

set /SYS/ESM clear_fault_action=true

Are you sure you want to clear /SYS/ESMR/ESM (y/n)?

Set ???clear_fault_action” to ???true???

Replacing the Battery

The battery maintains system time when the server is powered off and a time server is

unavailable. If the server fails to maintain the proper time when powered off and not connected

to a network, replace the battery.

Replacing Motherboard Assembly Components

157

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды