Oracle Sun Netra X4270 Скачать руководство пользователя страница 62

Страница: 62 / 238

BIOS Firmware Updates

■

Select Disabled to disable the Option ROM setting.

Press the F10 key to save the changes and exit the BIOS Setup utility.

Related Information

■

“Access the BIOS Setup Utility Menus” on page 46

■

“Option ROM Allocation” on page 60

■

“Exit the BIOS Setup Utility” on page 70

BIOS Firmware Updates

Each BIOS firmware version is paired and qualified with a specific ILOM SP firmware

version. Whenever you update the ILOM SP firmware, you will update the BIOS firmware. For

instructions about updating the ILOM SP firmware, refer to the ILOM 3.0 documentation

Related Information

■

Oracle Integrated Lights Out Manager (ILOM) 3.0 Web Interface Procedure Guide

■

Oracle Integrated Lights Out Manager (ILOM) 3.0 CLI Procedures Guide

■

ILOM 3.0 documentation

Understanding BIOS Setup Screens

The BIOS Setup utility reports system information and can be used to configure the server

BIOS settings. These topics display examples of the BIOS Setup utility screens.

Note -

The BIOS menus shown are examples and reflect the optimal defaults at startup. The

BIOS version numbers, menu information, and menu selections are subject to change over the

life of the product.

Note -

The BIOS Setup utility is stored in the BIOS flash memory. The configured data is

provided with context-sensitive help and is stored in the system's battery-backed CMOS RAM.

If the configuration stored in the CMOS RAM is invalid, the BIOS settings default to the

original state specified at the factory.

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды