Oracle Sun Netra X4270 Скачать руководство пользователя страница 52

Страница: 52 / 238

Set Watchdog Timers

■

Disabled – Watchdog timer disabled

Set one or both Watchdog timers and set the timeout durations in minutes.

■

SP BIOS Watchdog timer – The SP will perform the selected timer action if the BIOS hangs

or crashes during POST once it reaches the timeout duration.

■

SP OS Watchdog timer – The SP will perform the selected timer action if the Watchdog

timer is not restarted by an OS application before the timer reaches its timeout duration.

Press the F10 key to save the changes and exit BIOS utility.

Alternately, you can select the Exit screen, then select Save Changes and Exit.

Related Information

■

“Access the BIOS Setup Utility Menus” on page 46

■

“Exit the BIOS Setup Utility” on page 70

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды