Oracle Sun Netra X4270 Скачать руководство пользователя страница 132

Страница: 132 / 238

Replacing DIMMs

Related Information

■

“Remove the Air Duct” on page 127

■

“Replacing Fan Tray 0” on page 189

Replacing DIMMs

Caution -

This procedure requires that you handle components that are sensitive to static

discharge. This sensitivity can cause the component to fail. To avoid damage, ensure that you

follow antistatic practices as described in

“Electrostatic Discharge Safety” on page 74

Caution -

Ensure that all power is removed from the server before removing or installing

DIMMs, or damage to the DIMMs might occur. You must disconnect all power cables from the

system before performing this procedure.

The system supports a variety of DIMM configurations that can include quad-rank DIMMs,

dual-rank DIMMs, or single-rank DIMMs. When replacing or upgrading a DIMM on the server,

consider the following:

Description

Links

Learn the location of the DIMM slots in relation to the

CPUs.

“DIMM and CPU Physical Layout” on page 133

Learn the rules to follow when installing DIMMs in

slots.

“DIMM Population Rules” on page 134

“DIMM Considerations and Limitations” on page 135

Understand the classification rank labels on DIMMs.

“DIMM Rank Classification Labels” on page 136

Review how the system detects and logs ECC fault

information.

“Error Correction and Parity” on page 136

Identify and remove the faulty DIMMs from the server.

“Identify and Remove Faulty DIMMs” on page 137

Install replacement or new DIMMs.

“Install DIMMs” on page 141

Related Information

■

“Replacing the Air Duct” on page 127

■

“Replacing CPUs” on page 160

132

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды