Oracle Sun Netra X4270 Скачать руководство пользователя страница 34

Страница: 34 / 238

Inspect Internal Server Components

For the LED locations and descriptions of their behavior, see the service procedures for the

motherboard components.
To light these LEDs, hold down the Locator LED button on the server back panel or front panel

for 5 seconds to initiate a “push-to-test” mode that illuminates all other LEDs both inside and

outside of the chassis for 15 seconds.

Note -

The server must be in standby power mode for viewing the internal LEDs. If necessary,

reconnect the power cables to the server. Disconnect the power cables after inspecting these

LEDs.

Verify that there are no loose or improperly seated components.

Verify that all cable connectors inside the system are firmly and correctly

attached to their appropriate connectors.

Verify that any after-factory components are qualified and supported.

Check with your customer representative for information about which PCIe2 cards and DIMMs

are supported.

Check that the installed DIMMs comply with the supported DIMM population

rules and configurations.

For more information, see

“DIMM Population Rules” on page 134

Return the server to operation.

See

“Returning Server to Operation” on page 211

Use a pen, or other pointed object, to press and release the recessed power

button on the server front panel.

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды