Oracle Sun Netra X4270 Скачать руководство пользователя страница 11

Страница: 11 / 238

Using This Documentation

This service manual is for experienced system engineers with training in servicing Oracle Sun

Netra X4270 server. The manual contains detailed instructions for troubleshooting, repairing,

and upgrading server components. To use the information in this document, you must have

experience working with advanced server technology.

Note -

All internal components except hard drives must be installed by qualified service

technicians only.

Product Documentation Library

Documentation and resources for this product and related products are available at

http://

docs.oracle.com/cd/E19874-01/index.html

Related Documentation

Documentation

Links

All Oracle products

http://www.oracle.com/documentation

Sun Netra X4270 server

http://www.oracle.com/pls/topic/lookup?ctx=E19417-01&id=homepage

Integrated Lights Out Manager

(ILOM) 3.0

http://www.oracle.com/pls/topic/lookup?ctx=ilom30

Feedback

Provide feedback on this documentation at:

http://www.oracle.com/goto/docfeedback

Using This Documentation

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды