manualshive.com logo in svg

Oracle Sun Netra X4270, Руководство по обслуживанию

Поделиться
Скачать
Oracle Sun Netra X4270 Скачать руководство пользователя страница 115

Remove PCIe2 Cards From Slots 4 and 5

Related Information

■

“PCIe2 Slot Characteristics” on page 112

■

“Replacing PCIe2 Cards in Slots 4 and 5” on page 115

Replacing PCIe2 Cards in Slots 4 and 5

Note - 

Prior to replacing or installing a PCIe2 card, refer to the card documentation for specific

installation and cabling instructions.

■

“Remove PCIe2 Cards From Slots 4 and 5” on page 115

■

“Install PCIe2 Cards Into Slots 4 and 5” on page 117

Related Information

■

“Replacing Lower PCIe2 Cards” on page 123

Remove PCIe2 Cards From Slots 4 and 5

1.

Prepare the server for service

See 

“Preparing the Server for Component Replacement” on page 75

.

2.

With the PCI mezzanine installed and cabled, identify which card is to be

removed.

3.

Disconnect any external or internal cables connected to the card.

Replacing Motherboard Assembly Components

115

Содержание Sun Netra X4270















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды