Oracle Sun Netra X4270 Скачать руководство пользователя страница 144

Страница: 144 / 238

Remove a Flash Module

Caution -

Disconnect all power cables from the server prior to removing or installing a flash

module.

■

“Remove a Flash Module” on page 144

■

“Install a Flash Module” on page 146

Remove a Flash Module

Prepare the server for service.

See

“Preparing the Server for Component Replacement” on page 75

Remove the PCI mezzanine and place it on an antistatic mat.

See

“Remove the PCI Mezzanine” on page 102

Locate the installed flash modules on the motherboard in PCIe2 slot 0.

Identify the faulty flash module by pressing the Fault Remind button on the

motherboard and viewing the flash module fault and power LEDs.

144

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды