Oracle Sun Netra X4270 Скачать руководство пользователя страница 146

Страница: 146 / 238

Install a Flash Module

Remove the flash module by pressing down both ejector levers until the flash

module partially ejects from its socket.

Carefully lift the flash module out of its socket and place it on an antistatic mat.

Consider your next step:

■

If you removed the flash module as part of another procedure, return to that procedure.

■

Otherwise, continue to

“Install a Flash Module” on page 146

Related Information

■

“Install a Flash Module” on page 146

Install a Flash Module

Prepare the server for service.

See

“Preparing the Server for Component Replacement” on page 75

Remove the PCI mezzanine and place it on an antistatic mat.

See

“Remove the PCI Mezzanine” on page 102

Unpack the flash module and place it on an antistatic mat.

Ensure that the flash module socket ejector levers are open (rotated outward).

Align the notch in the flash module with the key in the motherboard socket.

This notch ensures that the flash module is oriented correctly.

Using both thumbs, press the flash module straight down into the socket until

both ejector levers click, locking the flash module into the slot.

The flash module must be inserted evenly, straight down into the slot until the flash module

locks into place.

Consider your next step:

■

If you installed the flash module as part of another procedure, return to that procedure.

■

Otherwise, continue with this task.

Replace the PCI mezzanine.

146

Sun Netra X4270 Server • September 2015

Содержание Sun Netra X4270















































































































































































































































Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды

Oracle Sun Netra X4270, Руководство по обслуживанию

Результаты поиска

Содержание Sun Netra X4270

Отзывы:

Бренды по названию

Популярные бренды