manualshive.com logo in svg

Oracle Sun Netra X4270, Руководство по обслуживанию

Поделиться
Скачать
Oracle Sun Netra X4270 Скачать руководство пользователя страница 15

Locating Controls and Connectors

Front Panel Components on Two-Drive Systems

With Bezel Removed

No.

Description

Additional Information

1

User alarm LEDs

Top to bottom – Critical LED, Major LED, Minor LED, User LED

Note - 

Also displayed through the front bezel

2

System status LEDs

Left to right – Locator LED button, Service Required LED, System Activity LED, Power button

Note - 

Also displayed through the front bezel

3

Optical media drive

Labeled DVD

4

Drive 1

Labeled 1

5

Drive 0

Labeled 0

6

Drive LEDs

Top to bottom – OK to Remove LED, Service Required LED, Power OK LED

Related Information

■

“Front Panel Controls On Two-Drive System” on page 14

■

“System Status LEDs” on page 19

■

“User Alarm LEDs” on page 20

■

“Drive LEDs” on page 21

Understanding the Server

15

Содержание Sun Netra X4270















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды