NTT docomo FOMA N700?, Руководство пользователя

Страница: 81 / 597

78
Mak
ing
/R
eceiving
Vid
eo-p
h
o
n
e
Calls
Using the function menu in the video-phone number input display
In the video-phone number input display...
a
P. 77
1
p
(FUNC)
s
Choose from the following options:
Display Reason
Check the number and retry You dialed the number incorrectly.
Busy The called party is on another call or using i-mode or packet communication.
Out of service area or power off The called party is out of signal range or his/her phone is turned off.
Driving mode The called party’s phone is in Driving mode.
Select on for the Call ID Notification When the call is made without notifying caller ID (When connecting to M-stage
V-LIVE or Visualnet).
Your call is being forwarded The call is being forwarded.
Failed to connect When you connect with no caller ID:
・ Set the caller ID notification to “ON”.
(This message may be displayed for the reason other than the above.)
Note
● The icon flashes while you are dialing a video-phone call and is displayed continuously during the call. If the call is dialed at the “32K”
dialing speed, flashes.
● During a hands-free call, is displayed and the other party’s voice is played through the FOMA terminal speaker. Pressing
o
( )
again switches hands-free mode off and changes to .
● Always keep the FOMA terminal away from your ear during a hands-free call. Holding the FOMA terminal close to your ear could adversely affect
your hearing or damage your ear.
● If an attempted “64K” video-phone call fails to connect when “Voice call auto switch” is set to “ON”, it automatically switches to the “32K” dialing
speed. If the video-phone call still fails to connect, it switches to voice-call mode. The table below shows how “Voice call auto switch” and automatic
connection speed switching operate when a video-phone call fails to connect.
● If you make a video-phone call to a phone that does not support video-phone calls, or if the called party’s phone supports video-phone calls but is
out of signal range or switched off, no connection can be established. If you called a phone that does not support video-phone calls and “Voice call
auto switch” is set to “ON”, the call is cut off by the called party before the video-phone connection is established and is then automatically redialed
as a voice call. However, this operation may not be carried out if you dial the wrong number or if you call an ISDN synchronous 64K or PIAFS access
point or an ISDN video-phone that does not conform to the 3G-324M standard (as at February 2005). Note that call charge may apply in some
cases.
● Once a video-phone is successfully connected, it is not re-dialed as a voice call.
● During a video-phone call with the FOMA terminal, if the call is forwarded, a message appears saying that the call is being forwarded.
● If you make a video-phone call to an emergency number (110, 119 or 118) from the FOMA terminal, the call is automatically changed to a voice call.
● If the “Recharge battery” battery low alarm appears on the display during a video-phone call, the other party sees the “Camera Off” message and
the call is disconnected roughly 20 seconds later.
● The digital communication charge is required when a substitute image is displayed during a video-phone call.
● A substitute image is displayed if you do not receive any image because of the other party’s setting.
● You cannot receive i-mode mail or a Message Request/Free during a video-phone call. Received mail is held at the i-mode center and can be
retrieved using “Check new message” once the video-phone is completed.
● You can receive SMS during a video-phone call.
● You cannot enter phone numbers and make video-phone calls while “Keypad dial lock”, “Restrict dialing” is set.
“Voice call auto
switch” set to ON The dialing speed automatically changes to “32K”. If
the video-phone call still fails to connect, it switches
to voice-call mode. Switches to voice-call mode.
“Voice call auto
switch” set to OFF
The dialing speed automatically changes to “32K”. If
the video-phone call still fails to connect, the
video-phone call ends.
Ends the video-phone call.
Dialing speed set to “64K” Dialing speed set to “32K”