NI GPIB-410 Скачать руководство пользователя страница 74

Страница: 74 / 145

Tutorial

Appendix A

GPIB-410 User Manual

A-4

© National Instruments Corp.

•

The GPIB-410 is set to participate in the handshake during capture.

•

The next capture operation will stop when the capture buffer is full
and the buffer will not be automatically written to the disk.

Press <F2> to return to the Main Menu. Enable the capturing by
pressing <Alt-C>.

CAP

appears on the right side of the title/status bar.

NDAC also becomes asserted on the GPIB-410 monitor because the
GPIB-410 is participating in the GPIB handshake as a Listener. Switch
to Monitor Input Mode by pressing <Alt-M>.

MON

appears beside

CAP

in the title/status bar. The menu screen appears as follows:

Figure A-3. Main Menu Screen with Monitor Input and Capturing Enabled

The GPIB-410 is now waiting for any of the selected GPIB events to
occur so that samples can be taken.

Содержание GPIB-410

















































































































































Результаты поиска

Содержание GPIB-410

Отзывы:

Бренды по названию

Популярные бренды

NI GPIB-410, Руководство пользователя

Результаты поиска

Содержание GPIB-410

Отзывы:

Бренды по названию

Популярные бренды