manualshive.com logo in svg

NI GPIB-410, Руководство пользователя

Поделиться
Скачать
NI GPIB-410 Скачать руководство пользователя страница 19

© National Instruments Corp.

2-1

GPIB-410 User Manual

Chapter 2
Hardware and Software Installation

                                                                                                      

This chapter contains the steps for installing your hardware and software.

Install your GPIB-410 using the following steps:

1.

Configure the hardware.

2.

Install the hardware.

3.

Review the files on the distribution diskette.

4.

Run the hardware diagnostics.

These steps are described in detail in the remainder of this chapter.

Step 1 – Configure the Hardware

The GPIB-410 hardware is configured at the factory.  Verify that the
settings of the GPIB-410 do not conflict with another board in your
system.  The factory configuration parameters are as follows:

•

The GPIB-410 occupies 32 contiguous bytes of I/O space.  The base
address of this 32-byte block of addresses can be any multiple of 20
hex, ranging from 000 hex to 3E0 hex.  The GPIB-410 is configured
at the factory with a base address of 300 hex, therefore occupying
addresses 300 to 31F hex of your PC I/O space.  If another board in
your system uses one or more of these addresses, refer to Appendix
C to change the GPIB-410 base address and to match the software
configuration to the new address.

•

The GPIB-410 uses DMA channel 1 on your PC for high-speed data
transfers.  If another board is already using DMA channel 1, refer to
Appendix C to change the GPIB-410 DMA channel and to match
the software configuration to the new channel.

•

The GPIB-410 uses Interrupt Line 7 of the PC I/O channel.  If
another board is already using Interrupt Line 7, refer to Appendix C

Содержание GPIB-410


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды