manualshive.com logo in svg

NI GPIB-410, Руководство пользователя

Поделиться
Скачать
NI GPIB-410 Скачать руководство пользователя страница 48

Chapter 4

Software Reference

© National Instruments Corp.

4-11

GPIB-410 User Manual

•

You type <Alt-T> again.

•

The last pattern in the pattern sequence is matched.

If the entire pattern sequence is satisfied before triggering is disabled,
the selected trigger action is taken.  While the GPIB-410 waits for a
particular pattern to occur the pattern label is highlighted.

Keep the following points in mind when defining the Trigger Spec.

•

The GPIB-410 hardware can detect only one trigger pattern at a
time without reprogramming.

•

The multi-pattern, repeating trigger capability of the GPIB-410 is
implemented in software.  If two events matching consecutive
patterns occur within a sufficiently small time interval, it is possible
the second event will be missed.

•

If the selected trigger action is 

TRIGGER

 

with

 

position:

TTTTT

, background capturing may be started when the trigger is

armed.  If so, following satisfaction of the pattern sequence there is
a brief capture adjustment period, during which time it is possible
that some capture entries may be missed or lost.

•

The likelihood of losing trigger or capture events can be reduced or
eliminated by configuring the GPIB-410 to participate in the
acceptor handshake while capturing (see Capture Settings screen)
or by enabling the "dummy" ACP handshaker <Alt-A>.

•

For triggering a capture operation, the following Trigger Spec is the
least dependent on software intervention and the most efficient.

1 WAIT FOR 

<single trigger pattern>

0001 time

then

TRIGGER with position:

T

The Trigger Specification screen contains the following fields.

•

Data/Control Specification

•

Trigger Repeat Factor

Содержание GPIB-410


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды