NI GPIB-410 Скачать руководство пользователя страница 106

Страница: 106 / 145

© National Instruments Corp.

D-1

GPIB-410 User Manual

Appendix D
Common Problems

This appendix contains possible causes for common problems
encountered when operating the GPIB-410.

Problem:

The capture operation does not terminate, even though
enough capture events have occurred to fill up the capture
buffer.

Possible Cause:

•

The

Action

when

buffer

full

field on the Capture Settings

screen is set to

reset

and

continue

. Change this value to

stop

capture

•

The value contained in the Interrupt Jumper Setting field on the
Configuration Settings screen does not match the actual jumper
setting on the interface board. Check the hardware configuration
and enter the proper value.

Problem:

There are no highlighted cursors present on the Capture
Display screen.

Possible Cause:

•

The capture buffer is empty. There must be data displayed on the
screen and capturing must be OFF for the cursors to be visible.

•

The contrast on your display is set too low. Adjust the contrast until
the highlighted cursors appear.

Содержание GPIB-410

















































































































































Результаты поиска

Содержание GPIB-410

Отзывы:

Бренды по названию

Популярные бренды

NI GPIB-410, Руководство пользователя

Результаты поиска

Содержание GPIB-410

Отзывы:

Бренды по названию

Популярные бренды