Mitsubishi Electric MELSOFT FR Configurator2, Инструкция по эксплуатации

Страница: 44 / 230

43
1. OUTLINE
1.4 Connection and parameter setting
1
2
3
4
5
6
7
8
9
10
NOTE
• Always reset the inverter after making the setting of the parameters. After you have changed the communication-related
parameters, communication cannot be established until the inverter reset.
• Set "5001" in any parameter from Pr.1076 to Pr.1078 to enable automatic recognition or switching to online connection during
communication through "CPU module" or "Ethernet module". When the initial settings are used, there is no need to change.
(Refer to
page 72 .)
• FR-E700-NE
1442
N660
IP filter address 1 (Ethernet) 0 0 to 255
Set the range of connectable IP addresses for the
network devices.
(When
Pr.1442 to Pr.1445 = "0 (initial value)", the
function is invalid.)
1443
N661
IP filter address 2 (Ethernet) 0 0 to 255
1444
N662
IP filter address 3 (Ethernet) 0 0 to 255
1445
N663
IP filter address 4 (Ethernet) 0 0 to 255
1446
N664 IP filter address 2 range specification
(Ethernet)
9999 0 to 255, 9999
1447
N665 IP filter address 3 range specification
(Ethernet)
9999 0 to 255, 9999
1448
N666 IP filter address 4 range specification
(Ethernet)
9999 0 to 255, 9999
1449
N670 Ethernet command source selection IP
address 1
0 0 to 255
Set the range of IP addresses to limit the network
devices that can be used as a command source during
Ethernet communication (with MODBUS/TCP
protocol).
When
Pr.1449 to Pr.1452 = "0 (initial value)", no IP
address is specified for command source selection via
Ethernet. In this case, operation commands cannot be
sent via Ethernet with MODBUS/TCP protocol.
When four or more clients attempt a connection to the
inverter during MODBUS/TCP protocol
communication, the connection attempted from
outside of the IP address range set for Ethernet
command source selection may be forced to be
closed.
1450
N671 Ethernet command source selection IP
address 2
0 0 to 255
1451
N672 Ethernet command source selection IP
address 3
0 0 to 255
1452
N673 Ethernet command source selection IP
address 4
0 0 to 255
1453
N674 Ethernet command source selection IP
address 3 range specification
9999 0 to 255, 9999
1454
N675 Ethernet command source selection IP
address 4 range specification
9999 0 to 255, 9999
Pr. Name
Initial
value
Setting range Description
442 Default gateway address 1 0 0 to 255
Enter the IP address of the default gateway, which is a
device connecting the different networks, to establish a
communication between the inverter and the devices
outside the inverter network.
443 Default gateway address 2 0 0 to 255
444 Default gateway address 3 0 0 to 255
445 Default gateway address 4 0 0 to 255
550
NET mode operation command
source selection
0
0
The Ethernet connector is the command interface enabled
in the NET operation mode.
2
The PU connector is the command interface enabled in the
NET operation mode.
805 Ethernet IP address 1 192 0 to 255
Enter the IP address of the inverter to be connected to
Ethernet.
806 Ethernet IP address 2 168 0 to 255
807 Ethernet IP address 3 50 0 to 255
808 Ethernet IP address 4 1 0 to 255
809 Subnet mask 1 255 0 to 255
Enter the subnet mask of the network to which the inverter
belongs.
810 Subnet mask 2 255 0 to 255
811 Subnet mask 3 255 0 to 255
812 Subnet mask 4 0 0 to 255
830
Ethernet communication network
number
1 1 to 239 Enter the network number.
831
Ethernet communication station
number
1 1 to 120 Enter the station number.
832
Link speed and duplex mode
selection
0 0 to 4
Set the communication speed and the communication
mode (full-duplex/half-duplex).
Pr. Name
Initial
value
Setting range
Description