manualshive.com logo in svg

Mart Cyclone 30 Series, Инструкция по установке, эксплуатации и обслуживанию, Страница: 294 / 322

Поделиться
Скачать
Mart Cyclone 30 Series Скачать руководство пользователя страница 294

Weekly

2 chnls

Yearly

2 chnls

Yearly

4 chnls

11. Troubleshooting

◆

Self-check function

When an error occurs, the following error codes are displayed.

Error code

e1
e2

Meaning

CPU error

Memory error

Output

OFF
OFF

Countermeasures

Press              .
Press              .

◆

Troubleshooting

If there is a problem with the Time Switch, check the following items.

Problems

The Time Switch does not operate 
when the power is turned ON.
The Time Switch 
does not operate 
according to the 
settings.

Output does not turned ON when the 
OUT ON/OFF switch is set to ON.
The time is fast or 
slow.

The display does 
not appear.
The display is 
incorrect.
There is a black spot on the 
LCD display's surface.

Check items

Is the power actually ON? Check that the
indicator is turned on.
Is the Time Switch wired correctly?
Check the wiring.
Is the OUT ON/OFF switch set to AUTO?
Is the Time Switch set correctly?
Isn't the Time Switch set for holiday operation?
Isn't the Time Switch set for override and automatic return operation?
Isn't the Time Switch set for day override operation?
(Weekly type only)
Isn't the Time Switch set for yearly operation? 
(Yearly types only)
Are banks (weekly type only) or seasons 
(yearly types only) set correctly?
Is the power actually ON? 
Check that the        indicator is turned on.
The time accuracy is influenced by the ambient temperature. 
Correct the present time in time adjustment mode.
Is theTime Switch installed in a location subject to 
excessive noise?   Timing performance may be 
adverserly affected if the Time Switch is installed in 
a location subject to excessive noise. Separate the 
Time Switch from any sources of noise.
If no Key input is entered within 2 minutes with 
the power OFF, the display is turned off.
The Time Switch may be affected by noise or surge. 
Separate the Time Switch from any sources of noise.
Black spot may appear due to static electricity. 
The spot disappears after a while.

Section

<Operation>2

<Installation>2,3

<Operation>2
<Operation>4

<Operation>5-1
<Operation>5-8

<Operation>5-4

<Operation>4-6

<Operation>6-4
<Operation>6-5

<Operation>2

<Operation>9
<Operation>3

 

−

<Operation>7

− 

 

− 

RESET

RESET

Содержание Cyclone 30 Series



































































































































































































































































































































Отзывы:

Нет отзывов