Mart Cyclone 30 Series Скачать руководство пользователя страница 149 | Manualshive

Страница: 149 / 322

Mart Cyclone 30 Series Скачать руководство пользователя страница 149

Maintenance

5 - 13

Standard Turntable Power Washer v. 4.0

The MART Corporation

2.2. Heating System

This section describes maintenance procedures for the following:

·

Air intake - burner blower motor (clean)

·

Burner blower motor (oil)

2.2.1.

Air Intake - Burner Blower Motor (Clean)

Clean the air intake on the burner blower motor (natural gas, L.P. gas, or fuel-oil fired
burners only) with a compressed-air blower or a soft brush, in order to remove dust and
dirt. Refer to the following figure.

2.2.2.

Burner Blower Motor (Oil)

Oil the burner blower motor with a standard electric-motor oil, suitable for small electric
motors. For example, 10W-50 SAE oil. Refer to the following figure.

Fig. 5 - 7: Burner Blower Motor (380,000 BTU Burner Shown; Other Sizes Similar)

«
...
147
148
149
150
151
...
»

Содержание Cyclone 30 Series



































































































































































































































































































































Отзывы:

Нет отзывов