Mart Cyclone 30 Series Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 322

Mart Cyclone 30 Series Скачать руководство пользователя страница 21

Important Safety Instructions and Warnings

Safety - 1

Standard Turntable Power Washer v. 4.0

The MART Corporation

Important Safety

Instructions and

Warnings

The following important safety instructions and warnings apply to installing,
operating, maintaining, and troubleshooting the MART Power Washer. They also
apply to repairing the washer, or to working with it in any way.

Read all of the following safety instructions and warnings thoroughly

before

you

install, operate, maintain, troubleshoot, repair the washer, or work with the
washer in any way!

SAVE THE SAFETY INSTRUCTIONS AND WARNINGS IN THIS
SECTION!

GENERAL SAFETY INSTRUCTIONS FOR OPERATING THIS
PRODUCT:

1. Read all safety and operating instructions/procedures

before installing, operating, maintaining, repairing, or
troubleshooting the washer ... or working with it in any
way.

2. Know how to STOP the washer. Be familiar with all its

controls.

3. Stay alert at all times, and watch what you are doing.

4. Do not operate the washer if you are tired, or if you have

had anything alcoholic to drink, or if you have taken any
drugs, including prescription medications.

5. Keep the operating area clear of people.

6. Do not overreach or stand on unstable support. Keep

good footing and balance at all times.

7. Follow the instructions given in this manual for installation,

operations, maintenance, and troubleshooting.

«
...
19
20
21
22
23
...
»

Содержание Cyclone 30 Series



































































































































































































































































































































Отзывы:

Нет отзывов