Mart Cyclone 30 Series Скачать руководство пользователя страница 125 | Manualshive

Страница: 125 / 322

Mart Cyclone 30 Series Скачать руководство пользователя страница 125

Advanced Operations: Process-Control

4 - 13

Standard Turntable Power Washer v. 4.0

The MART Corporation

3. Rinse-System Control (optional ARC)

The Automatic Rinse System (ARC) is a fresh-water rinsing system. It is powered by
waterline pressure. It allows the operator to control rinse characteristics and the
application of a rust inhibitor by means of the chemical injector pump.

The following controls rinse time:

·

Amount of makeup water needed, due to water loss through
evaporation or drag-out.

·

Automatic rinse system (ARC) timer

In controlling rinse cycle time, water loss takes priority

. The amount of makeup water

required determines the maximum rinse time allowed, if any.

Set rinse cycle duration by adjusting the automatic rinse cycle (ARC) timer, located in
the electrical control panel. Refer to Fig. 4-2.

WARNING! Disconnect power before opening the control
panel to make adjustments.

3.1. Setting the Rinse Timer

The rinse timer is an adjustable timer with a range of 0-10 minutes.

Fig. 4 - 3: Automatic Rinse Cycle (ARC) Timer Increments

Rinse

Timer (0-10min)

«
...
123
124
125
126
127
...
»

Содержание Cyclone 30 Series



































































































































































































































































































































Отзывы:

Нет отзывов